27W DMX 带闪烁盘

LED－DMX Series Light source Manual

（LED-27/45/75/100/150DMX）

Brief Introduction

Welcome to use LED-DMX series light source, which adopt advanced micro-electronics control technology, controlling lighting by converting international popular DMX512 standard digital control signal into analogue control signal; RGB light source have 7 channels, each light source have 7 codes. RGBW light source have 8 channels, each light source have 8 codes. Each channel can make 256 control levels, Mainly use DMX console to control light source

1, Performance Parameter:

Input power AC 100-120V or AC 220-240V 50/60HZ

Output intensity 256 steps

Signal input DMX512

DMX512 socket Standard XLR-3 Caron plug

Occupied site code RGB light source has 7 channels (1,8,15,22,29…….)

RGBW light source has 8 channels (1,9,17,25,33…….)

2, Basic function

1. International standard DMX512 input protocol, nixie tube setting program or address, etc;

2. 0-100% dimming output, 256 gray levels in total;

3. The light source is equipped with 7 light test modes, 7 levels of static brightness, 8 levels of change speed and 2 sound control modes;

4. The light source is equipped with 9 flashing speeds and 1 voice controlled flashing mode

5. The shell of the light source is made of aluminum alloy, with good heat dissipation to ensure longer led life

6. 75W and 100W have high temperature protection, and the system will automatically power off when the shell exceeds 50 degrees

7. Offline synchronization function. When the signal line is not connected, it can be adjusted to the same mode. Under the speed, it can change color synchronously

8. Flicker stop function. When flicker is not required, the flash disk does not block the light, and all optical fibers can output light

3，Usage

basic usage

MENU Main menu switch/exit submenu

UP parameter adjustment

DOWN parameter adjustment

ENTER Confirm/save/enter the submenu

After startup, press manu to select the contents of the main menu, then press up and down to adjust the parameters, and finally press enter to confirm.

Color change speed adjustment: in the color change mode, press and hold the Enter key, while pressing down to enter the speed adjustment menu.

Monochrome brightness adjustment: in monochrome mode, long press enter and press down to enter the brightness adjustment menu without letting go.

Voice control sensitivity adjustment: in the voice control mode, press and hold the Enter key, while pressing down to enter the sensitivity adjustment menu.

4，Channel table（controlled mode）

Channel NO.	Numerical Range	Functional Instruction
1	0~255	Total dimming, with "light cutting" function: When the "total dimming" channel value is 0-10, the program continues to run without light output, which can be called“ Software "cut light". The difference from the "hardware cutting" mode such as "Blackout" key is that it only works on this console (Group) light, and will not cause the console data to be cleared. Channel value 10-225: brightness adjustment.
2	0~255	Motor speed adjustment: The channel value is 0-10: the motor does not rotate, and the flash wheel set optical fiber is not blocked. 11-200: including 9 speed values; 201-250: 1, 2, 3 and 4 RPM respectively; 251-255: motor voice control.
3	0~255	Self variable regulation: When the channel value is 0, RGBW light brightness adjustment is effective for channels 5, 6, 7 and 8. 1-240: self propelled mode corresponding to a1-a13; 240-250: voice control 1; 251-255: voice control 2
4	0~255	Self propelled speed adjustment: Channel value 0-255: speed adjustment.(valid when the value of the third channel is 1-240.)
5	0~255	Red brightness adjustment
6	0~255	Green brightness adjustment
7	0~255	Blue brightness adjustment
8	0~255	White brightness adjustment （RGB don’t have this channel）

5，Channel table（Built in mode）

Image	Light mode	Meaning of number	Supplementary notes
	Fixed coloe mode	The middle number: 1 red, 2 green, 3 blue, 4 pure white, 5 yellow, 6 sky blue, 7 rose red, 8 mixed color white; Tail number 0:stops flashing, 1:lowest speed, 9:highest speed, Horizontal bar: voice control of speed	Press manu to switch the middle number, and press up / down to switch the tail number
	Color change mode	The middle number: 9 jump, 10 gradient, 11 breathing, 12 gliding, 13 automatic cycle; Tail number 0 :stops twinkle, 1 : the lowest speed, 9: the highest speed, Horizontal bar: voice control of speed
	Voice control mode	The middle number: 1 voice control（1）， 2 voice control（2）; Tail number 0 :stops twinkle 1 : the lowest speed, 9: the highest speed, Horizontal bar: voice control of speed
	Console mode	1. Please ensure that there is only one signal source (one console or one host). 2. If the signal source is disconnected (such as turning off the console or main engine), the light will be turned off automatically.	Press manu to switch the middle number, and press enter to save. See channel table for functions
	Remote control settings	IroF: Turn off remote control funtion ， IroN: turn on remote control function	Press manu to switch and enter to save。
	Brightness settings	Parameter range 1-7; 1: the lowest brightness， 7: the highest brighness	Secondary parameter adjustment ---- when the screen is adjusted to the corresponding mode, press and hold the Enter key, and press down while not letting go. After entering, press up and down to adjust the parameters, and finally press manu to exit.
	Change speed settings	Parameter range 0-7; 0: the lowest speed， 7:the highest speed
	Voice control sensitivity setting	Parameter range 0-42; 0:the lowest sensitivity，42:the highest sensitivity

6, control system connection

7, Attention of Installation and usage

1， This series of light source only can use the power supply mentioned in the manual, otherwise, it will damage the light source.

2，If make the connection of multi light sources, please use 2*0.5 wire with screening one by one to form a network.

3，Please check the connected wire at regularly , and change ageing, rustiness , as well as which insulated cover has been damaged.

4，The working surrounding of light source should be ventilated, dry, non-corrosion , non combustible gas and without any smoke in the place.

5, When signal wire of all light source are connected well, then switch on the current to work, avoiding to pull out signal wire with working current.